DIY, how to build your own cantilever sliding gate (5) – Weld the galvanized pipes into a gate frame

Welding was the only worrisome part of this project when I decided to build this cantilever gate because I never welded before, nor do I own a welding machine. And I had no idea of the difference between MIG welding and ARC welding. Fortunately I made a wise decision to buy a ARC welding machine, which plugs into your outlet just like other appliances, and most importantly, it did a great job. Forget about MIG welding if you don’t want to keep a gas tank in your garage….Negative side of the ARC welding is that the learning curve is steeper. But once you overcome all the difficulty as a beginner welder, ARC welding turns out to be a lot of fun!

Ugly welds I did on my gate...but they joints together pretty well. Maybe not too bad for a first time welder.
Ugly welds I did on my gate…but they joints together pretty well. Maybe not too bad for a first time welder?!

I purchased a 200AMP ARC welding machine from eBay, model BX1-200C1 for about $100. It is a simple, heavy and “analog” machine – no fancy LED indicators or digit display, all it has inside its steel case are sets of beefy coils, which, I believe, is to transform AC to low voltage DC for ARC welding. Electrical current could be adjusted through a knob, which actually is just pushing / pulling a metal core in / out of the coils to achieve various transformer turn ratio.

Front control panel of the BX1-200C1 200 AMP welding machine.
Front control panel of the BX1-200C1 200 AMP welding machine.

The BX1-200C1 welding machine comes with a unfinished power cord, so you will need to wire a plug on the power cord. The color code on the power code is probably the Europe/China standard, in which brown stand for live, blue for neutral and  green strip for ground. Since I was going to source the power from a standard 110VAC outlet from garage, I wired the cord onto a U.S. NEMA 5-15P plug. Having a 25-amp circuit breaker for the garage, I was a little worried in the beginning whether my garage circuit is beefy enough to handle power consumption. Amazingly, the breaker only tripped very few times when my washing machine was also spinning at full speed in the garage. When the welding machine is the sole electricity user, it worked perfectly fine without any glitches.

Wiring schematics for the BX1-200C1 welding machine: Brown - Live; Blue - Neutral; Green/Yellow - Ground.
Wiring schematics for the BX1-200C1 welding machine: Brown – Live; Blue – Neutral; Green/Yellow – Ground.
Plug wired per the color coding.
Plug wired per the color coding.

I didn’t get to try the 220VAC mode yet, as 110VAC already gave me more than enough power to finish my gate project with 1/8″ welding electrodes. I guess 220VAC will be necessary when thicker than 1/8″ electrodes are required for heavier-duty jobs.

Properly fastening/clamping your metal parts is another critical step to yield a successful weld. Parts to be welded together must stay solidly together during the welding process. I used the same “parallel clamping” idea as I did to set the post, in which I set up two pieces of wood stud of exactly same length perpendicularly to ensure same distance between the galvanized pipes. In order to fasten everything together before welding, I used the same tie-down straps during the transportation step. The following picture shows my work setup during the welding process.

Wood studs and tie-down straps used to fasten the pipes together.

Check out the video for the actual welding process.

Once the frame is mostly welded together, it is time to hang the whole thing onto the post. The 18 ft gate was really long, I had to cut down vegetables to make some room. The weight of the gate frame is still manageable at this point, but definitely I needed help from others. I continued to weld more pipes (diagonal direction) on to make the frame more structurally sound. It was actually easier to weld when the frame was up.

Hang the welded gate frame on the post. The frame will ride on the cantilever rollers.
Hang the welded gate frame on the post. The frame will ride on the cantilever rollers.
The gate slides! Very smooth....while, there are not too much things on it yet.
The gate in “close” position. Slides very smooth!….while, there are not too much things on it yet.
The gate frame in
The gate frame in “open” position.

28 Replies to “DIY, how to build your own cantilever sliding gate (5) – Weld the galvanized pipes into a gate frame”

  1. Hello can you explain the wiring colour and pinout for the 220v mode. I would like to change mines from 110 plug to 220. Plz help me

  2. Hello can you explain the wiring colour and pinout for the 220v mode. I would like to change mines from 110 plug to 220. Plz help me

  3. Just a safety note: You should grind, sand, or etch the zinc plating off galvanized pipe where you weld it, and wear a respirator. Google “metal fume fever”. A $40 welding helmet from Harbor Freight would have made this easier, since you would have had both hands to steady or hold the rod. A $25 3M P100 respirator would have also helped keep the zinc particulates out of your lungs. Since you were doing this outside and your welds appear more a “series of spot welds” than a true fillet joint that heated a large area, I guess it worked OK for you. Just a note in case someone else is inspired to duplicate your project.

    Congratulations on a nice project!

    1. Thank you for this video. It’s great to see people try new things. Don’t worry about the comments about your welding. Those welds are just fine for what they do.

      Is the gate still functioning good?

      Thanks
      Kirk

  4. Just a safety note: You should grind, sand, or etch the zinc plating off galvanized pipe where you weld it, and wear a respirator. Google “metal fume fever”. A $40 welding helmet from Harbor Freight would have made this easier, since you would have had both hands to steady or hold the rod. A $25 3M P100 respirator would have also helped keep the zinc particulates out of your lungs. Since you were doing this outside and your welds appear more a “series of spot welds” than a true fillet joint that heated a large area, I guess it worked OK for you. Just a note in case someone else is inspired to duplicate your project.

    Congratulations on a nice project!

    1. Thank you for this video. It’s great to see people try new things. Don’t worry about the comments about your welding. Those welds are just fine for what they do.

      Is the gate still functioning good?

      Thanks
      Kirk

  5. I followed this and built my own gate with a few modifications. Im super happy with how it turned out and have been running it for at least 6 months.

  6. I followed this and built my own gate with a few modifications. Im super happy with how it turned out and have been running it for at least 6 months.

  7. Hello,
    what was the post spacing? I plan to put a 10ft gate, so my counterweight would be 5ft (total 15ft). Would the posts be spaced 5ft apart? Thanks!

Leave a Reply to XueMing Cancel reply

Your email address will not be published.

This site uses Akismet to reduce spam. Learn how your comment data is processed.